S: Postville-Besitzer, die noch keinen TRIM-Support haben

Hallo Forum,

ich arbeite gerade daran, die Intel-Firmware-Updates auf SSDs zu flashen, die zwar Intel-Hardware verbaut haben, aber nicht Intel-branded sind. Zu diesem Zweck suche ich Leute, die eine Postville-SSD haben, deren Firmware noch _KEINEN_ TRIM-Support bietet, die diesen aber theoretisch durch den Intel SSD Firmware Updater nachruechsten koennten (wenn sie denn wollten). Wenn sich hier so jemand herumtreibt, bitte, bitte per PM bei mir melden.

Dankeschoen!

hab auch ne 80gb postville und noch keine zeit/lust gehabt die firmware zu flashen. ich müsste auch eine der ersteren oben haben.

Hab nur die Serial Nummer & unique ID rausgenommen:


ATA device, with non-removable media
Model Number: INTEL SSDSA2M080G2GC
Serial Number: xxxxxxxxxxxxxxxxxxxxx
Firmware Revision: 2CV102G2
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6
Standards:
Used: ATA/ATAPI-7 T13 1532D revision 1
Supported: 7 6 5 4
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 156301488
LBA48 user addressable sectors: 156301488
Logical Sector size: 512 bytes
Physical Sector size: 512 bytes
device size with M = 1024*1024: 76319 MBytes
device size with M = 1000*1000: 80026 MBytes (80 GB)
cache/buffer size = unknown
Nominal Media Rotation Rate: Solid State Device
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
Device-initiated interface power management
* Software settings preservation
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
supported: enhanced erase
2min for SECURITY ERASE UNIT. 2min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5001517958f858b1
NAA : 5
IEEE OUI : 001517
Unique ID : xxxxxxxx
Checksum: correct

Danke fuer eure Zuschriften!

Ich habe, was ich wollte: http://johannes.truschnigg.info/blo...ntel-Controller

Tja… das kommt davon, wenn man & in URIs nicht korrekt escaped
(fixed.)