frage zu partitionieren, formatieren und eintrag in fstab?

fdisk /dev/ataraid

[...] prtitionieren nach wunsch [...]

$(EDITOR) /etc/fstab

(sollte ausreichend kommentiert sein) legt fest, welche partition wo unter / per default gemountet werden soll.

hth, colo

mkfs.[fstpye] /dev/partition

z.b.

mkfs.ext3 /dev/hda3

das dev/ataraid ist scheinbar irgendwas anderes, nur nicht mein raidcontroller

habe es nun endlich geschafft einen kernel zu kompilieren und auch das modul für den controller zu installieren. seltsamerweise bei modprobe findet er das modul nicht, aber im log hab ich folgende zeilen gefunden:

Code:

May 20 16:01:29 MIKNET-SRV1 kernel: PCI: Found IRQ 12 for device 00:0b.1
May 20 16:01:29 MIKNET-SRV1 kernel: PCI: Sharing IRQ 12 with 00:10.3
May 20 16:01:29 MIKNET-SRV1 kernel: Found PTI SuperTrak at mbase: 0xdf000000, irq 12.
May 20 16:01:29 MIKNET-SRV1 kernel: scsi0 : PROMISE SuperTrak SX6000 Driver
May 20 16:01:29 MIKNET-SRV1 kernel:   Vendor: PTI       Model: SuperTrak         Rev:     
May 20 16:01:29 MIKNET-SRV1 kernel:   Type:   Direct-Access                      ANSI SCSI revision: 02
May 20 16:01:29 MIKNET-SRV1 kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
May 20 16:01:29 MIKNET-SRV1 kernel: SCSI device sda: 1991484800 512-byte hdwr sectors (1019640 MB)
May 20 16:01:29 MIKNET-SRV1 kernel:  sda: unknown partition table
May 20 16:05:34 MIKNET-SRV1 kernel: Kernel logging (proc) stopped.
May 20 16:05:34 MIKNET-SRV1 kernel: Kernel log daemon terminating.

nun habe ich fdisk sda versucht, aber damit konnte ich den controller nicht partitionieren.

wie bringe ich nun meinen controller zum funktionieren?

tia

MIK

kann nicht darauf zugreifen oder so ähnlich. sollte der genaue wortlaut wichtig sein, nur sagen und ich werf die ksite an.

MIK

fehlermeldung vom fdisk: unable to open /sda

ich hab jetzt dmesg gemacht, da fehlt seltsamerweise der raidcontroller aber bei insmod ist keine fehlermeldung gekommen.

hab grad nochmals insmod gemacht, jetzt ist es dabei. muß man insmod bei jedem start machen? is ja unpraktisch.

Code:

Linux version 2.4.26 (root@MIKNET-SRV1) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 SMP Thu May 20 15:08:50 CEST 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
 BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 VIA694                                    ) @ 0x000f6a20
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Kernel command line: auto BOOT_IMAGE=Linux ro root=302
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1595.493 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3185.04 BogoMIPS
Memory: 514432k/524224k available (2146k kernel code, 9400k reserved, 867k data, 172k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU:             Common caps: 0383fbff c1c3fbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU:             Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU0: AMD Duron(tm) processor stepping 00
per-CPU timeslice cutoff: 182.90 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1595.4643 MHz.
..... host bus clock speed is 265.9107 MHz.
cpu: 0, clocks: 2659107, slice: 1329553
CPU0<T0:2659104,T1:1329536,D:15,S:1329553,C:2659107>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfb3e0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/3177] at 00:11.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10f
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Compaq SMART2 Driver (v 2.4.28)
HP CISS Driver (v 2.4.50)
pcnet32.c:v1.28 02.20.2004 [email]tsbogend@alpha.franken.de[/email]
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: pci dev 00:0a.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 11 for device 00:0a.0
PCI: Sharing IRQ 11 with 00:10.2
PCI: Sharing IRQ 11 with 00:11.5
eth0: RealTek RTL8139 at 0xe081a000, 00:08:54:00:fa:34, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
HDLC support module revision 1.14b
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: IBM-DTTA-371010, ATA DISK drive
blk: queue c047d600, I/O limit 4095Mb (mask 0xffffffff)
hdc: MATSHITADVD-ROM SR-8583A, ATAPI CD/DVD-ROM drive
hdd: RICOH CD-R/RW MP7040A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 19746720 sectors (10110 MB) w/465KiB Cache, CHS=19590/16/63, UDMA(33)
hdc: attached ide-cdrom driver.
hdc: ATAPI 32X DVD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
hdd: attached ide-cdrom driver.
hdd: ATAPI 20X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Partition check:
 hda: hda1 < hda5 > hda2
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
SCSI subsystem driver Revision: 1.00
Red Hat/Adaptec aacraid driver (1.1-3 May 20 2004 15:10:23)
DC390: 0 adapters found
3ware Storage Controller device driver for Linux v1.02.00.037.
3w-xxxx: No cards found.
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
Adding Swap: 499928k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
spurious 8259A interrupt: IRQ7.
end_request: I/O error, dev 02:00 (floppy), sector 0
end_request: I/O error, dev 02:00 (floppy), sector 0
PCI: Found IRQ 12 for device 00:0b.1
PCI: Sharing IRQ 12 with 00:10.3
[b]Found PTI SuperTrak at mbase: 0xdf000000, irq 12.
scsi0 : PROMISE SuperTrak SX6000 Driver
  Vendor: PTI       Model: SuperTrak         Rev:     
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 1991484800 512-byte hdwr sectors (1019640 MB)
 sda: unknown partition table[/b]

Zitat von kleinerChemiker

fehlermeldung vom fdisk: unable to open /sda

as COLOSSUS said: /dev/sda gibts bestimmt

Zitat

ich hab jetzt dmesg gemacht, da fehlt seltsamerweise der raidcontroller aber bei insmod ist keine fehlermeldung gekommen.

hab grad nochmals insmod gemacht, jetzt ist es dabei. muß man insmod bei jedem start machen? is ja unpraktisch.

nö, du musst blos die pti_st in die /etc/modules eintragen, dann passiert das automatisch.

solved:
das modul war im falschen verzeichnis, dadurch wurde es nicht geladen und so weiter ...

MIK