c147258
- - - - - - -
|
Servus....^^ hätte folgendes Problem: nachdem meine IDE Platte eingegangen ist hab ich erfolgreich das komplette System auf die neue HDD "gecloned" und kann damit auch starten usw... Jedoch hab ich zur Zeit ein Problem mit einer externen 2,5" HDD, welche per USB 2.0 eingebunden wird. Die HDD wird zwar erkannt aber nachdem folgende Meldung kommt: usb-storage: device scan complete wird die HDD nicht zum Beispiel als sda angegeben. Somit ist auch kein Zugriff möglich. Wenn ich jedoch das System mit Ubuntu oder ähnliches boote, wird problemlos die externe Festplatte erkannt. Hättet ihr Lösungsvorschläge? Danke! Vor 2 Tagen oder so hat das jedoch alles problemlos funktioniert! usb 4-4: new high speed USB device using ehci_hcd and address 5
usb 4-4: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
|
c147258
- - - - - - -
|
modprobe -l *usb* ; modprobe -l *hci*
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dtt200u.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dibusb-mb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-digitv.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dibusb-mc.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-dibusb-common.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-vp702x.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-nova-t-usb2.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-a800.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-vp7045.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-cxusb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-gp8psk.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/dvb-usb/dvb-usb-umt-010.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/b2c2/b2c2-flexcop-usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/ttusb-dec/ttusb_dec.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/ttusb-dec/ttusbdecfe.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/video/pvrusb2/pvrusb2.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/video/usbvideo/usbvideo.ko
/lib/modules/2.6.18-6-686/kernel/drivers/media/video/cpia_usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/isdn/gigaset/usb_gigaset.ko
/lib/modules/2.6.18-6-686/kernel/drivers/isdn/hisax/hfc_usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/core/usbcore.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/atm/xusbatm.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/atm/usbatm.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/class/usblp.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/storage/usb-storage.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/usbled.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/sisusbvga/sisusbvga.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/usbtest.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/usblcd.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/legousbtower.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/misc/ldusb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/net/plusb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/net/usbnet.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/ir-usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/ti_usb_3410_5052.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/kl5kusb105.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/serial/usbserial.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbmouse.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbkbd.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbhid.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/input/usbtouchscreen.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/mon/usbmon.ko
/lib/modules/2.6.18-6-686/kernel/drivers/net/irda/irda-usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/char/watchdog/pcwd_usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/bfusb.ko
/lib/modules/2.6.18-6-686/kernel/sound/usb/snd-usb-lib.ko
/lib/modules/2.6.18-6-686/kernel/sound/usb/usx2y/snd-usb-usx2y.ko
/lib/modules/2.6.18-6-686/kernel/sound/usb/snd-usb-audio.ko
/lib/modules/2.6.18-6-686/kernel/drivers/ieee1394/ohci1394.ko
/lib/modules/2.6.18-6-686/kernel/drivers/scsi/ahci.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/host/ehci-hcd.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/host/ohci-hcd.ko
/lib/modules/2.6.18-6-686/kernel/drivers/usb/host/uhci-hcd.ko
/lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_vhci.ko
/lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_usb.ko
/lib/modules/2.6.18-6-686/kernel/drivers/bluetooth/hci_uart.ko
/lib/modules/2.6.18-6-686/kernel/drivers/mmc/sdhci.ko
dmesg
Linux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-22etch2) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Aug 18 08:42:39 UTC 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff40000 (usable)
BIOS-e820: 000000003ff40000 - 000000003ff50000 (ACPI data)
BIOS-e820: 000000003ff50000 - 0000000040000000 (ACPI NVS)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 261952
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32576 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f5db0
ACPI: RSDT (v001 A M I OEMRSDT 0x05000406 MSFT 0x00000097) @ 0x3ff40000
ACPI: FADT (v001 A M I OEMFACP 0x05000406 MSFT 0x00000097) @ 0x3ff40200
ACPI: OEMB (v001 A M I OEMBIOS 0x05000406 MSFT 0x00000097) @ 0x3ff50040
ACPI: DSDT (v001 1ABSP 1ABSP001 0x00000001 MSFT 0x02000001) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 50000000 (gap: 40000000:c0000000)
Detected 1500.093 MHz processor.
Built 1 zonelists. Total pages: 261952
Kernel command line: root=/dev/hda3 ro
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030676k/1047808k available (1541k kernel code, 16456k reserved, 580k data, 196k init, 130304k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3002.22 BogoMIPS (lpj=6004456)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9fbbf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: a7e9fbbf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9fbbf 00000000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0e30)
CPU0: Intel(R) Pentium(R) M processor 1500MHz stepping 05
SMP motherboard not detected.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4786k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI Error (evregion-0317): No handler for Region [ECOR] (c18ef63c) [EmbeddedControl] [20060707]
ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBRG.EC0_.ACS_] (Node c18f4f40), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.AC__._INI] (Node c18f4c34), AE_NOT_EXIST
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI Error (evregion-0317): No handler for Region [ECOR] (c18ef63c) [EmbeddedControl] [20060707]
ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBRG.EC0_.BATS] (Node c18f4f2c), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.BAT0._STA] (Node c18f7414), AE_NOT_EXIST
ACPI Error (uteval-0212): Method execution failed [\_SB_.BAT0._STA] (Node c18f7414), AE_NOT_EXIST
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:09: ioport range 0x480-0x48f has been reserved
pnp: 00:09: ioport range 0x5c0-0x5cf has been reserved
pnp: 00:0d: ioport range 0x540-0x55f has been reserved
pnp: 00:0d: ioport range 0x400-0x47f could not be reserved
pnp: 00:0d: ioport range 0x480-0x48f has been reserved
pnp: 00:0d: ioport range 0x500-0x53f has been reserved
pnp: 00:0d: ioport range 0x4c0-0x4cf has been reserved
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: ff800000-ff8fffff
PREFETCH window: ce900000-de9fffff
PCI: Bus 3, cardbus bridge: 0000:02:01.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 52000000-53ffffff
MEM window: 54000000-55ffffff
PCI: Bus 7, cardbus bridge: 0000:02:01.1
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 56000000-57ffffff
MEM window: 58000000-59ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 1000-1fff
MEM window: ff900000-ff9fffff
PREFETCH window: dea00000-deafffff
PCI: Enabling device 0000:00:1e.0 (0106 -> 0107)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
PCI: Setting latency timer of device 0000:02:01.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:01.1[B] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:02:01.1 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1220242074.016:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
ACPI: Invalid PBLK length [7]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (59 C)
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000e800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000e880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 9, io base 0x0000ec00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Time: acpi_pm clocksource has been installed.
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 10, io mem 0xffaffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
usb 4-1: new high speed USB device using ehci_hcd and address 2
hda: ST960815A, ATA DISK drive
usb 4-1: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-R6112, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
tg3.c:v3.65 (August 07, 2006)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0e:a6:aa:1b:94
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
ACPI: PCI Interrupt 0000:02:01.2[C] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9] MMIO=[ff9ef800-ff9effff] Max Packet=[2048] IR/IT contexts=[4/4]
hda: max request size: 512KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000318798f]
Adding 2048276k swap on /dev/hda2. Priority:-1 extents:1 across:2048276k
EXT3 FS on hda3, internal journal
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.3)
ath_rate_sample: 1.2 (0.9.3)
ath_pci: 0.9.4.5 (0.9.3)
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.9 phy 4.3 radio 3.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0xff9d0000, irq=4
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [email]dm-devel@redhat.com[/email]
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: AC Adapter [AC] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
PM: Writing back config space on device 0000:02:00.0 at offset b (was 3ed173b, writing 17351043)
PM: Writing back config space on device 0000:02:00.0 at offset 3 (was 0, writing 4010)
PM: Writing back config space on device 0000:02:00.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:02:00.0 at offset 1 (was 2b00000, writing 2b00106)
PM: Writing back config space on device 0000:02:00.0 at offset 0 (was 3ed173b, writing 169c14e4)
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
Installing knfsd (copyright (C) 1996 [email]okir@monad.swb.de[/email]).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized radeon 1.25.0 20060524 on minor 0
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
mtrr: 0xd0000000,0x8000000 overlaps existing 0xd0000000,0x4000000
mtrr: 0xd0000000,0x8000000 overlaps existing 0xd0000000,0x4000000
mtrr: 0xd0000000,0x8000000 overlaps existing 0xd0000000,0x4000000
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:drm_unlock] *ERROR* Process 2315 using kernel context 0
usb 4-1: USB disconnect, address 2
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 4
usb 2-1: device not accepting address 4, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 5
usb 2-1: device not accepting address 5, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 6
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 7
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 8
usb 2-1: device not accepting address 8, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 9
usb 2-1: device not accepting address 9, error -71
usb 4-4: new high speed USB device using ehci_hcd and address 5
usb 4-4: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
usb 4-4: USB disconnect, address 5
usb 4-4: new high speed USB device using ehci_hcd and address 6
usb 4-4: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
usb 4-4: USB disconnect, address 6
usb 4-3: new high speed USB device using ehci_hcd and address 7
usb 4-3: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
usb 4-3: USB disconnect, address 7
usb 4-1: new high speed USB device using ehci_hcd and address 8
usb 4-1: configuration #1 chosen from 1 choice
[B]scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 8
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
[/B]
usb 4-1: USB disconnect, address 8
usb 4-3: new high speed USB device using ehci_hcd and address 9
usb 4-3: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
usb 4-2: new high speed USB device using ehci_hcd and address 15
usb 4-2: new high speed USB device using ehci_hcd and address 19
usb 4-2: new high speed USB device using ehci_hcd and address 29
usb 4-2: new high speed USB device using ehci_hcd and address 33
usb 4-2: new high speed USB device using ehci_hcd and address 36
usb 4-2: new high speed USB device using ehci_hcd and address 42
ehci_hcd 0000:00:1d.7: port 2 reset error -110
hub 4-0:1.0: hub_port_status failed (err = -32)
usb 4-2: new high speed USB device using ehci_hcd and address 54
ehci_hcd 0000:00:1d.7: port 2 reset error -110
hub 4-0:1.0: hub_port_status failed (err = -32)
usb 4-2: new high speed USB device using ehci_hcd and address 65
usb 4-2: new high speed USB device using ehci_hcd and address 69
ehci_hcd 0000:00:1d.7: port 2 reset error -110
hub 4-0:1.0: hub_port_status failed (err = -32)
ehci_hcd 0000:00:1d.7: port 2 reset error -110
hub 4-0:1.0: hub_port_status failed (err = -32)
hub 4-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
usb 4-2: new high speed USB device using ehci_hcd and address 76
usb 4-2: new high speed USB device using ehci_hcd and address 99
usb 4-2: new high speed USB device using ehci_hcd and address 111
usb 4-2: new high speed USB device using ehci_hcd and address 118
usb 4-2: new high speed USB device using ehci_hcd and address 121
usb 4-2: new high speed USB device using ehci_hcd and address 8
usb 4-2: new high speed USB device using ehci_hcd and address 10
usb 4-2: new high speed USB device using ehci_hcd and address 11
ehci_hcd 0000:00:1d.7: port 2 reset error -110
hub 4-0:1.0: hub_port_status failed (err = -32)
usb 4-2: new high speed USB device using ehci_hcd and address 14
usb 4-2: new high speed USB device using ehci_hcd and address 27
usb 4-2: new high speed USB device using ehci_hcd and address 49
usb 4-2: new high speed USB device using ehci_hcd and address 56
usb 4-2: new high speed USB device using ehci_hcd and address 64
usb 4-2: new high speed USB device using ehci_hcd and address 69
usb 4-2: new high speed USB device using ehci_hcd and address 75
usb 4-2: new high speed USB device using ehci_hcd and address 76
usb 4-2: new high speed USB device using ehci_hcd and address 97
ehci_hcd 0000:00:1d.7: port 2 reset error -110
hub 4-0:1.0: hub_port_status failed (err = -32)
usb 4-2: new high speed USB device using ehci_hcd and address 100
hub 4-0:1.0: Cannot enable port 2. Maybe the USB cable is bad?
usb 4-2: new high speed USB device using ehci_hcd and address 101
usb 4-2: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 101
usb-storage: waiting for device to settle before scanning
usb 4-2: USB disconnect, address 101
usb 4-3: USB disconnect, address 9
usb 4-3: new high speed USB device using ehci_hcd and address 102
usb 4-3: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 102
usb-storage: waiting for device to settle before scanning
Vendor: IC25N040 Model: ATCS04-0 Rev: 0000
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
usb 4-3: USB disconnect, address 102
usb 4-3: new high speed USB device using ehci_hcd and address 103
usb 4-3: configuration #1 chosen from 1 choice
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 103
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
wifi0: stuck beacon; resetting (bmiss count 4)
Hab übrigens öfters das LW an/abgesteckt und wie man auch bei dmesg sieht auch noch ein anderes LW probiert... aber das hier sollte eingebunden werden: usb 4-3: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
Vendor: Hitachi Model: HTS541616J9SA00 Rev:
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: device scan complete
ls /dev/[hs]d[a-z]
ls command funktioniert irg. zur Zeit nicht... (anscheinend bin ich in einem anderen Modus, muss ich wohl zu Hause nochmals gucken...sry)
Schon vorab ... VIELEN VIELEN Dank!!!
Bearbeitet von c147258 am 01.09.2008, 14:18
|
c147258
- - - - - - -
|
Hallo, also ls Command funktioniert noch immer nicht und auch x-window hat eine Macke. Sprich der HDD Crash dürfte sich ordentlich auf die Debian Installation ausgewirkt haben. cat Command erkennt er auch nicht mehr... ls -alh / | grep dev
nbdeb:/# ls bash: ls: command not found Wenn ich per SFTP auf die "Kiste" schaue, dann ist unter /usr/local/bin oder sbin nichts vorhanden... gar nichts mehr -> dort sollten sich doch die ls Befehle usw. befinden... nbdeb:/# which ls
-> nix :(
nbdeb:/# echo $PATH
/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/bin/X11
Unter /usr/bin befindet sich schon einiges - jedoch kein ls grep plugdev < /etc/group
nbdeb:/# grep plugdev < /etc/group
plugdev:x:46:chris
EDIT: hätte jetzt Single User Mode probiert: folgendes kommt beim booten -> zb. das er die Befehle - chmod / chgrp / ln nicht findet und dann "Give root password for maintenance" (or type Control-D to continue): somit..vorerst vielen vielen Dank!..werd mich mal ans "reparieren dranmachen  "
|
Anmeldung